PreviousPro2 Power Supply 230Vac/24...
NextPro2 Power Supply 230Vac/24...

Pro2 Power Supply 230Vac/24Vdc 40A (960W)

WAGO Power supply; Pro 2; 1-phase; 24 VDC output voltage; 40 A output current; TopBoost + PowerBoost

Free shipping on Web orders over $100

$1122.00
(Each excl GST)
In Stock
Quantity Breaks
1+
5+
25+
$1,122.00
$1,122.00
$1,122.00
SKU: WAGO-2787-2448 Manufacturer part number: 2787-2448 Manufacturer: WAGO

Technical data

Nominal output voltage Uo nom DC 24 V (SELV)
Output voltage range DC 24 … 28 V (adjustable)
Default setting DC 24 V
Nominal output current Io nom 40 A (24 VDC)
Nominal output power 960 W
Control deviation ≤ 1 %
Residual ripple ≤ 70 mV (peak-to-peak)
Current limitation 1.1 x Io nom (typ.)
Overload behavior TopBoost/PowerBoost/Time-limited constant current mode (other overload behaviors can be set)
PowerBoost DC 60 A (5 s)
TopBoost up to 600 %
Power loss Pl ≤ 1.5 W (Standby); â‰¤ 2.4 W (No load); â‰¤ 40 W (230 VAC; Nominal load)
Efficiency (typ.) 96 % (230 VAC; 40 A; 25 °C); 96.3 % (230 VAC; 30 A; 25 °C)
Signaling Optical status indication (DC OK; load; warning and error states)
  Digital signal input and output (DI/DO)
Communication Communication interface, can be used with WAGO USB Communication Cable (750-923) or IO-Link Communication Module (2789-9080) or Modbus RTU Communication Module (2789-9015)
Internal fuse T 10 A / 250 VAC
Required backup fusing An external DC fuse is required for the DC input voltage.
Recommended backup fusing 16 A (for USA/Canada: 15 A)
Isolation voltage (pri.-sec., AC) 3,510 V
Isolation voltage (pri.-GND, AC) 2,200 V
Isolation voltage (Sec.-GND) DC 0.5 kV
Isolation voltage (Sec.-Signal) DC 0.5 kV
Protection class I
Protection type IP20 (per EN 60529)
Resistance to reverse feed ≤ DC 35 V
Overvoltage category III (≤ 2000 m a. s.l.); II (> 2000 m a. s.l.)
Pollution degree 2
Transient suppression (primary) Yes
Overvoltage protection; secondary Internal protective circuit
  ≤ 35 VDC (in the event of a fault)
Short-circuit-protected Yes
Open-circuit-proof Yes
Parallel operation Yes
Series operation Yes
MTBF > 900,000 h (per IEC 61709)
Phases 1
Nominal input voltage Ui nom 1 x AC 200 … 240 V
Input voltage range AC 180 … 264 V; DC 130 … 240 V
Nominal mains frequency range 47 … 63 Hz; 0 Hz
Input current Ii ≤ 4.3 A (240 VAC; Nominal load); â‰¤ 5.1 A (200 VAC; Nominal load)
Inrush current ≤ 10 A (after 1 ms)
Power factor ≥ 0.98  (240 VAC)
Power factor correction (PFC) Active
Mains failure hold-up time ≥ 25 ms (230 VAC)

Connection data

Connection type (1) Input/Signaling
Connection technology CAGE CLAMP®
WAGO Connector WAGO 721 Series
Solid conductor 0.08 … 2.5 mm² / 28 … 12 AWG
Fine-stranded conductor 0.08 … 2.5 mm² / 28 … 12 AWG
Fine-stranded conductor; with insulated ferrule 0.25 … 1.5 mm² / 20 … 16 AWG
Fine-stranded conductor; with uninsulated ferrule 0.25 … 2.5 mm² / 20 … 14 AWG
Strip length 8 … 9 mm / 0.31 … 0.35 inch
Connection type 2 Output
Connection technology 2 Push-in CAGE CLAMP®
WAGO Connector 2 WAGO 831 Series
Solid conductor 2 0.5 … 10 mm² / 20 … 8 AWG
Fine-stranded conductor 2 0.5 … 10 mm² / 20 … 8 AWG
Fine-stranded conductor; with insulated ferrule 2 0.5 … 6 mm²
Fine-stranded conductor; with uninsulated ferrule 2 0.5 … 6 mm²
Strip length 2 13 … 15 mm / 0.51 … 0.59 inch

Physical data

Width 120 mm / 4.724 inch
Height 130 mm / 5.118 inch
Depth from upper edge of DIN-rail 130 mm / 5.118 inch
Note (dimensions) Height without connector
  Height with connector: 169 mm

Mechanical data

Mounting type DIN-35 rail

 

SKU WAGO-2787-2448

GTIN 4055143878296

We strive to provide you with the best information we can, considering the images are not to scale and do not represent detailed perspectives of the respected products. If you notice any errors or omissions in this information, please let us know using the contact us tab on this page.
Products specifications
Attribute name Attribute value
Locally Stocked in Australia Only Show Stocked Items
*
*
*
This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.
Product Files
Type Name
Data Sheet
WAGO-2787-2448

Technical data

Nominal output voltage Uo nom DC 24 V (SELV)
Output voltage range DC 24 … 28 V (adjustable)
Default setting DC 24 V
Nominal output current Io nom 40 A (24 VDC)
Nominal output power 960 W
Control deviation ≤ 1 %
Residual ripple ≤ 70 mV (peak-to-peak)
Current limitation 1.1 x Io nom (typ.)
Overload behavior TopBoost/PowerBoost/Time-limited constant current mode (other overload behaviors can be set)
PowerBoost DC 60 A (5 s)
TopBoost up to 600 %
Power loss Pl ≤ 1.5 W (Standby); â‰¤ 2.4 W (No load); â‰¤ 40 W (230 VAC; Nominal load)
Efficiency (typ.) 96 % (230 VAC; 40 A; 25 °C); 96.3 % (230 VAC; 30 A; 25 °C)
Signaling Optical status indication (DC OK; load; warning and error states)
  Digital signal input and output (DI/DO)
Communication Communication interface, can be used with WAGO USB Communication Cable (750-923) or IO-Link Communication Module (2789-9080) or Modbus RTU Communication Module (2789-9015)
Internal fuse T 10 A / 250 VAC
Required backup fusing An external DC fuse is required for the DC input voltage.
Recommended backup fusing 16 A (for USA/Canada: 15 A)
Isolation voltage (pri.-sec., AC) 3,510 V
Isolation voltage (pri.-GND, AC) 2,200 V
Isolation voltage (Sec.-GND) DC 0.5 kV
Isolation voltage (Sec.-Signal) DC 0.5 kV
Protection class I
Protection type IP20 (per EN 60529)
Resistance to reverse feed ≤ DC 35 V
Overvoltage category III (≤ 2000 m a. s.l.); II (> 2000 m a. s.l.)
Pollution degree 2
Transient suppression (primary) Yes
Overvoltage protection; secondary Internal protective circuit
  ≤ 35 VDC (in the event of a fault)
Short-circuit-protected Yes
Open-circuit-proof Yes
Parallel operation Yes
Series operation Yes
MTBF > 900,000 h (per IEC 61709)
Phases 1
Nominal input voltage Ui nom 1 x AC 200 … 240 V
Input voltage range AC 180 … 264 V; DC 130 … 240 V
Nominal mains frequency range 47 … 63 Hz; 0 Hz
Input current Ii ≤ 4.3 A (240 VAC; Nominal load); â‰¤ 5.1 A (200 VAC; Nominal load)
Inrush current ≤ 10 A (after 1 ms)
Power factor ≥ 0.98  (240 VAC)
Power factor correction (PFC) Active
Mains failure hold-up time ≥ 25 ms (230 VAC)

Connection data

Connection type (1) Input/Signaling
Connection technology CAGE CLAMP®
WAGO Connector WAGO 721 Series
Solid conductor 0.08 … 2.5 mm² / 28 … 12 AWG
Fine-stranded conductor 0.08 … 2.5 mm² / 28 … 12 AWG
Fine-stranded conductor; with insulated ferrule 0.25 … 1.5 mm² / 20 … 16 AWG
Fine-stranded conductor; with uninsulated ferrule 0.25 … 2.5 mm² / 20 … 14 AWG
Strip length 8 … 9 mm / 0.31 … 0.35 inch
Connection type 2 Output
Connection technology 2 Push-in CAGE CLAMP®
WAGO Connector 2 WAGO 831 Series
Solid conductor 2 0.5 … 10 mm² / 20 … 8 AWG
Fine-stranded conductor 2 0.5 … 10 mm² / 20 … 8 AWG
Fine-stranded conductor; with insulated ferrule 2 0.5 … 6 mm²
Fine-stranded conductor; with uninsulated ferrule 2 0.5 … 6 mm²
Strip length 2 13 … 15 mm / 0.51 … 0.59 inch

Physical data

Width 120 mm / 4.724 inch
Height 130 mm / 5.118 inch
Depth from upper edge of DIN-rail 130 mm / 5.118 inch
Note (dimensions) Height without connector
  Height with connector: 169 mm

Mechanical data

Mounting type DIN-35 rail

 

SKU WAGO-2787-2448

GTIN 4055143878296

Products specifications
Attribute name Attribute value
Locally Stocked in Australia Only Show Stocked Items
Categories
Brands
Contact Info
1800 931 559

Mon-Fri 8:00am - 5:00pm

sales@lappaustralia.com.au
12 Grevillea St, Eastern Creek NSW

Australia

Information
Customer Service
Copyright © 2024 LAPP Australia. All rights reserved.