You have no items in your shopping cart.

Pro2 Power Supply 230Vac/24Vdc 5A (120W)

WAGO Power supply; Pro 2; 1-phase; 24 VDC output voltage; 5 A output current; TopBoost + PowerBoost

Free shipping on Web orders over $100

$422.00
(Each excl GST)
In Stock
Quantity Breaks
1+
5+
25+
$422.00
$422.00
$422.00
SKU: WAGO-2787-2144 Manufacturer part number: 2787-2144 Manufacturer: WAGO

Technical data

Internal fuse T 6.3 A / 250 VAC
Required backup fusing An external DC fuse is required for the DC input voltage.
Recommended backup fusing 16 A (for USA/Canada: 15 A)
Signaling Optical status indication (DC OK; load; warning and error states)
Digital signal input and output (DI/DO)
Communication Communication interface, can be used with WAGO USB Communication Cable (750-923) or IO-Link Communication Module (2789-9080) or Modbus RTU Communication Module (2789-9015)
Phases 1
Nominal input voltage Ui nom 1 x AC 100 … 240 V
Input voltage range AC 90 … 264 V; DC 130 … 240 V
Nominal mains frequency range 47 … 63 Hz; 0 Hz
Input current Ii ≤ 1 A (240 VAC; Nominal load); ≤ 1.8 A (100 VAC; Nominal load)
Inrush current ≤ 9 A (after 1 ms)
Power factor correction (PFC) Active
Mains failure hold-up time ≥ 20 ms (230 VAC)
Nominal output voltage Uo nom DC 24 V (SELV)
Output voltage range DC 24 … 28 V (adjustable)
Default setting DC 24 V
Nominal output current Io nom 5 A (24 VDC)
Nominal output power 120 W
Control deviation ≤ 1 %
Residual ripple ≤ 70 mV (peak-to-peak)
Current limitation 1.1 x Io nom (typ.)
Overload behavior TopBoost/PowerBoost/Time-limited constant current mode (other overload behaviors can be set)
PowerBoost DC 7.5 A (5 s)
TopBoost up to 600 %
Power loss Pl ≤ 1 W (Standby); ≤ 2 W (No load); ≤ 10 W (230 VAC; Nominal load)
Efficiency (typ.) 93.8 % (230 VAC; 5 A; 25 °C)
Isolation voltage (pri.-sec., AC) 3,510 V
Isolation voltage (pri.-GND, AC) 2,200 V
Isolation voltage (Sec.-GND) DC 0.5 kV
Isolation voltage (Sec.-Signal) DC 0.5 kV
Protection class I
Protection type IP20 (per EN 60529)
Resistance to reverse feed ≤ DC 35 V
Overvoltage category III (≤ 2000 m a. s.l.); II (> 2000 m a. s.l.)
Pollution degree 2
Transient suppression (primary) Yes
Overvoltage protection; secondary Internal protective circuit
≤ 35 VDC (in the event of a fault)
Short-circuit-protected Yes
Open-circuit-proof Yes
Parallel operation Yes
Series operation Yes
MTBF > 1,000,000 h (per IEC 61709)

Connection data

Connection type (1) Input/Output/Signaling
Connection technology CAGE CLAMP®
WAGO Connector WAGO 721 Series
Solid conductor 0.08 … 2.5 mm² / 28 … 12 AWG
Fine-stranded conductor 0.08 … 2.5 mm² / 28 … 12 AWG
Fine-stranded conductor; with insulated ferrule 2.5 … 1.5 mm² / 12 … 16 AWG
Fine-stranded conductor; with uninsulated ferrule 1.5 … 0.08 mm² / 16 … 28 AWG
Strip length 8 … 9 mm / 0.31 … 0.35 inch

Physical data

Width 35 mm / 1.378 inch
Height 130 mm / 5.118 inch
Depth from upper edge of DIN-rail 130 mm / 5.118 inch
Note (dimensions) Height without connector
  Height with connector: 166 mm

Mechanical data

Mounting type DIN-35 rail

SKU WAGO-2787-2144

GTIN 4055143907415

We strive to provide you with the best information we can, considering the images are not to scale and do not represent detailed perspectives of the respected products. If you notice any errors or omissions in this information, please let us know using the contact us tab on this page.
Products specifications
Attribute name Attribute value
Locally Stocked in Australia Only Show Stocked Items
*
*
*
This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.

Technical data

Internal fuse T 6.3 A / 250 VAC
Required backup fusing An external DC fuse is required for the DC input voltage.
Recommended backup fusing 16 A (for USA/Canada: 15 A)
Signaling Optical status indication (DC OK; load; warning and error states)
Digital signal input and output (DI/DO)
Communication Communication interface, can be used with WAGO USB Communication Cable (750-923) or IO-Link Communication Module (2789-9080) or Modbus RTU Communication Module (2789-9015)
Phases 1
Nominal input voltage Ui nom 1 x AC 100 … 240 V
Input voltage range AC 90 … 264 V; DC 130 … 240 V
Nominal mains frequency range 47 … 63 Hz; 0 Hz
Input current Ii ≤ 1 A (240 VAC; Nominal load); ≤ 1.8 A (100 VAC; Nominal load)
Inrush current ≤ 9 A (after 1 ms)
Power factor correction (PFC) Active
Mains failure hold-up time ≥ 20 ms (230 VAC)
Nominal output voltage Uo nom DC 24 V (SELV)
Output voltage range DC 24 … 28 V (adjustable)
Default setting DC 24 V
Nominal output current Io nom 5 A (24 VDC)
Nominal output power 120 W
Control deviation ≤ 1 %
Residual ripple ≤ 70 mV (peak-to-peak)
Current limitation 1.1 x Io nom (typ.)
Overload behavior TopBoost/PowerBoost/Time-limited constant current mode (other overload behaviors can be set)
PowerBoost DC 7.5 A (5 s)
TopBoost up to 600 %
Power loss Pl ≤ 1 W (Standby); ≤ 2 W (No load); ≤ 10 W (230 VAC; Nominal load)
Efficiency (typ.) 93.8 % (230 VAC; 5 A; 25 °C)
Isolation voltage (pri.-sec., AC) 3,510 V
Isolation voltage (pri.-GND, AC) 2,200 V
Isolation voltage (Sec.-GND) DC 0.5 kV
Isolation voltage (Sec.-Signal) DC 0.5 kV
Protection class I
Protection type IP20 (per EN 60529)
Resistance to reverse feed ≤ DC 35 V
Overvoltage category III (≤ 2000 m a. s.l.); II (> 2000 m a. s.l.)
Pollution degree 2
Transient suppression (primary) Yes
Overvoltage protection; secondary Internal protective circuit
≤ 35 VDC (in the event of a fault)
Short-circuit-protected Yes
Open-circuit-proof Yes
Parallel operation Yes
Series operation Yes
MTBF > 1,000,000 h (per IEC 61709)

Connection data

Connection type (1) Input/Output/Signaling
Connection technology CAGE CLAMP®
WAGO Connector WAGO 721 Series
Solid conductor 0.08 … 2.5 mm² / 28 … 12 AWG
Fine-stranded conductor 0.08 … 2.5 mm² / 28 … 12 AWG
Fine-stranded conductor; with insulated ferrule 2.5 … 1.5 mm² / 12 … 16 AWG
Fine-stranded conductor; with uninsulated ferrule 1.5 … 0.08 mm² / 16 … 28 AWG
Strip length 8 … 9 mm / 0.31 … 0.35 inch

Physical data

Width 35 mm / 1.378 inch
Height 130 mm / 5.118 inch
Depth from upper edge of DIN-rail 130 mm / 5.118 inch
Note (dimensions) Height without connector
  Height with connector: 166 mm

Mechanical data

Mounting type DIN-35 rail

SKU WAGO-2787-2144

GTIN 4055143907415

Products specifications
Attribute name Attribute value
Locally Stocked in Australia Only Show Stocked Items

Customers who bought this item also bought

Earth Tinned Flex - 110 Degree 1x10mm LAPP-3806200
$6.08
(Per/m excl GST)
In Stock
ETHERLINE® Cat5e Flex suitable for ProfiNet applications LAPP-2170886
$6.90
(Per/m excl GST)
Global Stock
UNITRONIC® LIYCY Screened, Black UV-resistant sheath, 2X0.5 BK LAPP-1030517
$4.22
(Per/m excl GST)
Global Stock
V90HT 1x0.5 orange AS/NZS 5000.1 Finely Stranded LAPP-3801009
$34.00
(100m excl GST)
In Stock
V90HT 1x0.5 violet AS/NZS 5000.1 Finely Stranded LAPP-3801007
$34.00
(100m excl GST)
In Stock